The aim of using silica gel sachets is to minimize the risk of irreversible damage to items in transit or store caused by condensing water vapour. By adsorbing water molecules, a silica gel sachet will decrease the Relative Humidity within a package to levels at which concentration will not happen .

Three main moisture sources need to be considered

(1) That from the air contained in the package.
(2) That from the packing added inside of the package (e.g. for cushioning purposes).
(3) That which diffuses through the outer packaging during storage or transit.

These factors are considered in British Standard 1133: Section 19:1968 as

(a) The area of the moisture barrier : A (in square meters).
(b) The type of moisture barrier : R is the moisture vapour transmission rate of a barrier (in grams per square meter per 24 hours, measured at 90% relative humidity and 38°C).
(c) The volume of the air inside the barrier : V (in cubic meters of the container).
(d) The weight and type of any packaging material inside the barrier. This is known as the damage factor : DF (D is the weight of packing material in grams and F is a factor depending on the type of damage and its probable moisture content).
(e) The length of time protection is required : M (in months).
(f) The type of climate   temperate (average 25°C and 75% relative humidity) or tropical (average 38°C and 90% relative humidity).

Typical R values are :

10 for a thin poly bag.
3.4 for a heavy duty poly bag (500 gauge).
2 for a heavy duty poly bag (1000 gauge).
0.05 for an aluminum barrier foil.

F values are : 1 & 5 for timber of moisture content higher than 14%.
1 & 8 for felt, carton board and similar general packaging work.
1 & 10 for plywood and timber with a moisture content less than 14%.

They are used in the following formulae :

For temperate climates W = 11 x A x R x M + DF
For tropical climates W = 40 x A x R x M + DF
For hermetically sealed containers W = 170 x V + DF

Where W is the weight of silica gel required in grams.

It is difficult to get exact weights of silica gel required from the above formulae owing to the many variables that have to be considered, some of which are difficult to measure. The formulae can, however, be a useful guide to indicate the amount of silica gel required to give adequate protection, it is often prudent to choose the nearest standard size silica gel sachet above the value that W comes out at. For large values of W, a more effective solution than using a single large sachet, is using a number of smaller sachets spread around the package. This will reduce the Relative Humidity at a faster rate.

Items especially at risk.

Condensation of water vapour from air will not occur, even when the relative humidity approaches 100%, providing the air temperature remains constant. So the risk of condensation (and therefore corrosion) arises mainly because of large drops in air temperature, where at the new lower temperature, the volume of water vapour is too much for the air to hold. Special attention needs to be paid in situations where

(a) Variations between daytime and night time temperatures reach 20   30°C.
(b) Seasonal temperature variations are large.
(c) Temperature variations occur due to the intermittent functioning of encased apparatus such as electrical conductors and resistors, fuses, circuit breakers or relay motors, which release calories when in use.

The greatest risk of condensation is in high humidity environments in Alexandria, where a drop of just 5°C will on average, cause water vapors to condense. As a general rule it is enough to maintain the relative humidity of the enclosed air below 30% to avoid all risk of condensation.

Silica Gel Sachets For Home Use

Silica gel can often be useful in domestic applications, but quite hard to find. To this end, we have three sizes of sachets available in smaller quantities, thus:

50 x 10 gram self indicating (blue to pink) silica gel sachets.
25 x 25 gram self indicating (blue to pink) silica gel sachets.
10 x 100 gram self indicating (blue to pink) silica gel sachets.

Kindly mention the requirement to enable us to give the quotation

Please remember also that there are applications to which silica gel isn't really suited. These are mainly damp but large and unsealed spaces such as: bathrooms, basements in Alexandria, sheds, caravans and cars (which are in regular use). Even quite large amounts of silica gel in areas such as these can quickly become exhausted and any improvement is often very short term only.

For any other requirements of any Chemicals in Alexandria, please mail us at vinod@innovacorporate.com Or amavinod@bol.net.in or call us on our Mobile No. +91-9312871070 OR 9911130697.